MB QUART MT OLYMPUS SERIES Spezifikationen Seite 8
- Seite / 17
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
DUAL AMP INSTALLATION PROCEDURE:
4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
5. Connect two 0 gauge ground cables directly to the chassis with in 36” of the amp.
puts with good quality RCA interconnect cables.
- Be sure to remove any paint or primer from the ground point.
2. Plug in the HFR-G1 bass remote module into the amp remote input DIN connection
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
on the Master amp. This will allow the Master amp to control both Master and Slave
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
amps with just one Bass Remote.
Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the
7. Connect the subwoofer(s) in accordance to the diagrams below.
Slave amp SLAVE INPUT. Note: This will “link” the amps so that the Master amp
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as
crossover switches will control both the Master and Slave amps. The Slave amp
shown below.
crossover switches will be bypassed.
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug the HFR-G1 remote module into the amp remote input DIN connection.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
FULL RANGE
STEREO LINE INPUT
NOT USED
Y-ADAPTOR
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line
output, you will need an optional “Y-Adaptor” as shown.
HERCULES / ATLAS MONO AMPLIFIER APPLICATIONS
Basic application
+12V GND
POWER
SPEAKER
REM
+
-
+
-
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
Linking two amps for single or dual subwoofer application
Amplifiers are stable to 2-Ohms linked
6
RCA JUMPER CABLE
MASTER OUTPUT TO SLAVE INPUT
SPEAKER OUTPUT
REM - - + +
POWER INPUT
BATT+12V GND
BATT+12V GNDBATT+12V GND
SPEAKER OUTPUT
REM - - + +
POWER INPUT
SPEAKER OUTPUT
REM - - + +
POWER INPUT
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY +12v
VIA FUSE
MONO
SUBWOOFER
1-OHM MINIMUM
INPUT OUTPUT LEVEL PHASE BOOST BANDWIDTH FREQUENCY SUBSONIC LOW PASS MODE MASTER OUT
9V 0.2V 0 180 0dB +10dB NARROW WIDE 30Hz 100Hz 15Hz 35Hz 35Hz 250Hz
SLAVE IN
SLAVE IN
MASTER OUT
PARAMETRIC BASS EQ
HFR-G1
REMOTE
L L
L
R R
R
POWER
PROTECT
INPUT OUTPUT LEVEL PHASE BOOST BANDWIDTH FREQUENCY SUBSONIC LOW PASS MODE MASTER OUT
9V 0.2V 0 180 0dB +10dB NARROW WIDE 30Hz 100Hz 15Hz 35Hz 35Hz 250Hz
SLAVE IN
SLAVE IN
MASTER OUT
PARAMETRIC BASS EQ
HFR-G1
REMOTE
L L
R R
POWER
PROTECT
INPUT OUTPUT LEVEL PHASE BOOST BANDWIDTH FREQUENCY SUBSONIC LOW PASS MODE MASTER OUT
9V 0.2V 0 180 0dB +10dB NARROW WIDE 30Hz 100Hz 15Hz 35Hz 35Hz 250Hz
SLAVE IN
SLAVE IN
MASTER OUT
PARAMETRIC BASS EQ
HFR-G1
REMOTE
L L
R R
POWER
PROTECT
DESIGNATED
MONO LINE INPUT
*
DESIGNATED
MONO LINE INPUT
*
MIN MAXX
CLIP
GREEN: PRE-CLIP
AMBER: SOFT CLIP
RED: HARD CLIP
GREEN: POWER
DIAGNOSTICS
RED: SHORT
AMBER: THERMAL
HFR-G1
MIN MAXX
CLIP
GREEN: PRE-CLIP
AMBER: SOFT CLIP
RED: HARD CLIP
GREEN: POWER
DIAGNOSTICS
RED: SHORT
AMBER: THERMAL
HFR-G1
12 GAUGE JUMPER WIRE
MODE MASTER OUT
SLAVE IN
SLAVE IN
MASTER OUT
MODE MASTER OUT
SLAVE IN
SLAVE IN
MASTER OUT
- MT OLYMPUS 1
- HIGH PERFORMANCE AMPLIFIERS 2
- HIFONICS MT OLYMPUS 2
- System Design 3
- Installation 3
- MT OLYMPUS AMPLIFIERS: 4
- FULL RANGE STEREO 5
- 4 CHANNEL FULL RANGE SYSTEM 6
- 2 or 3 CHANNEL SYSTEM 6
- MULTI-AMPLIFIER APPLICATIONS 7
- Basic application 8
- BASIC APPLICATION 9
- TROUBLESHOOTING A SYSTEM 11
- Maxxsonics Limited Warranty 13
- Accessories 14
- PART#: A213 17
Verwandte Produkte und Handbücher für Auto-Audio-Verstärker MB QUART MT OLYMPUS SERIES
(12 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.198 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern